.

param-docs/parameter-pages/GPIO/IO0.md

@@ -1,18 +1,13 @@
 # Parameter `IO0`
 Default Value: `input disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO0` pin.
-
 !!! Warning
     This pin is only usable with restrictions!
     It must be disabled when the camera is used.
     Additionally, it is used to activate Bootloader mode and must therefore be HIGH after a reset!
-
 Parameters:
-
 - `GPIO 0 state`: One of `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 0 use interrupt`: Enable interrupt trigger
 - `GPIO 0 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/IO1.md

@@ -1,16 +1,11 @@
 # Parameter `IO1`
 Default Value: `input disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO1` pin.
-
 !!! Warning
     This pin is by default used for the serial communication as TX pin (USB logging)!
-
 Parameters:
-
 - `GPIO 1 state`: One of `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 1 use interrupt`: Enable interrupt trigger
 - `GPIO 1 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/IO12.md

@@ -1,16 +1,11 @@
 # Parameter `IO12`
 Default Value: `input-pullup disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO12` pin.
-
 !!! Note
     This pin is usable without known restrictions!
-
 Parameters:
-
 - `GPIO 12 state`: One of `external-flash-ws281x`, `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 12 use interrupt`: Enable interrupt trigger
 - `GPIO 12 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/IO13.md

@@ -1,16 +1,11 @@
 # Parameter `IO13`
 Default Value: `input-pullup disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO13` pin.
-
 !!! Note
     This pin is usable without known restrictions!
-
 Parameters:
-
 - `GPIO 13 state`: One of `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 13 use interrupt`: Enable interrupt trigger
 - `GPIO 13 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/IO3.md

@@ -1,16 +1,11 @@
 # Parameter `IO3`
 Default Value: `input disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO3` pin.
-
 !!! Warning
     This pin is by default used for the serial communication as RX pin (USB logging)!
-
 Parameters:
-
 - `GPIO 3 state`: One of `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 3 use interrupt`: Enable interrupt trigger
 - `GPIO 3 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/IO4.md

@@ -1,17 +1,12 @@
 # Parameter `IO4`
 Default Value: `built-in-led disabled 10 false false`
-
 !!! Warning
     This is an **Expert Parameter**! Only change it if you understand what it does!
-
 This parameter can be used to configure the GPIO `IO4` pin.
-
 !!! Warning
     This pin is only usable with restrictions!
     By default, it is used for build-in flash light (onboard LED).
-
 Parameters:
-
 - `GPIO 4 state`: One of `built-in-led`, `input`, `input pullup`, `input pulldown` or `output`.
 - `GPIO 4 use interrupt`: Enable interrupt trigger
 - `GPIO 4 PWM duty resolution`: LEDC PWM duty resolution in bit

param-docs/parameter-pages/GPIO/LEDColor.md

@@ -1,5 +1,4 @@
 # Parameter `LEDColor`
 Default Value: `150 150 150`
-
 Color of the attached LEDs to GPIO12 in (R)ed, (G)reen (B)lue from `0` (full off) .. `255` (full on). 
 (See `IO12` parameter).

param-docs/parameter-pages/GPIO/LEDNumbers.md

@@ -1,4 +1,3 @@
 # Parameter `LEDNumbers`
 Default Value: `2`
-
 Number of LEDs on the external LED-stripe attached to GPIO12 (See `IO12` parameter).

param-docs/parameter-pages/GPIO/LEDType.md

@@ -1,4 +1,3 @@
 # Parameter `LEDType`
 Default Value: `WS2812`
-
 Type of the `WS2812x` which is connected to GPIO12 (See `IO12` parameter).

param-docs/parameter-pages/GPIO/MainTopicMQTT.md

@@ -1,10 +1,6 @@
 # Parameter `MainTopicMQTT`
 Default Value: `wasserzaehler/GPIO`
 
-
-
 !!! Note
     This parameter is not accessible through the Web Interface Configuration Page!
-
 Please fill me with an explanation and useful links
-