add shaffenmeisters PR and add web config

README.md

@@ -188,13 +188,14 @@ Ground -------------------------- coax signal ground
 The NVS parameter "display_config" sets the parameters for an optional display. Syntax is
 ```
 I2C,width=<pixels>,height=<pixels>[address=<i2c_address>][,reset=<gpio>][,HFlip][,VFlip][driver=SSD1306|SSD1326[:1|4]|SSD1327|SH1106]
-SPI,width=<pixels>,height=<pixels>,cs=<gpio>[,back=<gpio>][,reset=<gpio>][,speed=<speed>][,HFlip][,VFlip][driver=SSD1306|SSD1322|SSD1326[:1|4]|SSD1327|SH1106|SSD1675|ST7735|ST7789|ILI9341[:16|18][,rotate]]
+SPI,width=<pixels>,height=<pixels>,cs=<gpio>[,back=<gpio>][,reset=<gpio>][,speed=<speed>][,HFlip][,VFlip][driver=SSD1306|SSD1322|SSD1326[:1|4]|SSD1327|SH1106|SSD1675|ST7735|ST7789|ILI9341[:16|18][,rotate]][,mode=<mode>]
 ```
 - back: a LED backlight used by some older devices (ST7735). It is PWM controlled for brightness
 - reset: some display have a reset pin that is should normally be pulled up if unused
 - VFlip and HFlip are optional can be used to change display orientation
 - rotate: for non-square *drivers*, move to portrait mode. Note that *width* and *height* must be inverted then
 - Default speed is 8000000 (8MHz) but SPI can work up to 26MHz or even 40MHz
+- mode:  Default mode = 0.  Some display modules use different transaction line timings.  Check the module documentation if a non-standard mode is required.
 - SH1106 is 128x64 monochrome I2C/SPI [here]((https://www.waveshare.com/wiki/1.3inch_OLED_HAT))
 - SSD1306 is 128x32 monochrome I2C/SPI [here](https://www.buydisplay.com/i2c-blue-0-91-inch-oled-display-module-128x32-arduino-raspberry-pi)
 - SSD1322 is 256x64 grayscale 16-levels SPI in multiple sizes [here](https://www.buydisplay.com/oled-display/oled-display-module?resolution=159) - it is very nice

components/display/core/gds_default_if.h

@@ -11,7 +11,7 @@ bool GDS_I2CInit( int PortNumber, int SDA, int SCL, int speed );
 bool GDS_I2CAttachDevice( struct GDS_Device* Device, int Width, int Height, int I2CAddress, int RSTPin, int BacklightPin );
 
 bool GDS_SPIInit( int SPI, int DC );
-bool GDS_SPIAttachDevice( struct GDS_Device* Device, int Width, int Height, int CSPin, int RSTPin, int Speed, int BacklightPin );
+bool GDS_SPIAttachDevice( struct GDS_Device* Device, int Width, int Height, int CSPin, int RSTPin, int Speed, int BacklightPin, int Mode );
 
 #ifdef __cplusplus
 }

components/display/core/ifaces/default_if_spi.c

@@ -34,7 +34,7 @@ bool GDS_SPIInit( int SPI, int DC ) {
     return true;
 }
 
-bool GDS_SPIAttachDevice( struct GDS_Device* Device, int Width, int Height, int CSPin, int RSTPin, int BackLightPin, int Speed ) {
+bool GDS_SPIAttachDevice( struct GDS_Device* Device, int Width, int Height, int CSPin, int RSTPin, int BackLightPin, int Speed, int Mode ) {
     spi_device_interface_config_t SPIDeviceConfig = { };
     spi_device_handle_t SPIDevice;
 
@@ -48,6 +48,7 @@ bool GDS_SPIAttachDevice( struct GDS_Device* Device, int Width, int Height, int
     SPIDeviceConfig.clock_speed_hz = Speed > 0 ? Speed : SPI_MASTER_FREQ_8M;
     SPIDeviceConfig.spics_io_num = CSPin;
     SPIDeviceConfig.queue_size = 1;
+    SPIDeviceConfig.mode = Mode;
 	SPIDeviceConfig.flags = SPI_DEVICE_NO_DUMMY;
 	if (Device->SPIParams) Device->SPIParams(SPIDeviceConfig.clock_speed_hz, &SPIDeviceConfig.mode, 
 											 &SPIDeviceConfig.cs_ena_pretrans, &SPIDeviceConfig.cs_ena_posttrans);

components/display/display.c

@@ -119,14 +119,15 @@ void display_init(char *welcome) {
 		
 			ESP_LOGI(TAG, "Display is I2C on port %u", address);
 		} else if (strcasestr(config, "SPI") && spi_system_host != -1) {
-			int CS_pin = -1, speed = 0;
+			int CS_pin = -1, speed = 0, mode = 0;
 		
 			PARSE_PARAM(config, "cs", '=', CS_pin);
 			PARSE_PARAM(config, "speed", '=', speed);
+			PARSE_PARAM(config, "mode", '=', mode);
 		
 			init = true;
 			GDS_SPIInit( spi_system_host, spi_system_dc_gpio );
-			GDS_SPIAttachDevice( display, width, height, CS_pin, RST_pin, backlight_pin, speed );
+			GDS_SPIAttachDevice( display, width, height, CS_pin, RST_pin, backlight_pin, speed, mode );
 				
 			ESP_LOGI(TAG, "Display is SPI host %u with cs:%d", spi_system_host, CS_pin);
 		} else {

components/platform_console/cmd_i2ctools.c

@@ -101,6 +101,7 @@ static struct {
 	struct arg_int *reset;
 	struct arg_lit *clear;
 	struct arg_lit *invert;
+	struct arg_int *mode;
 	struct arg_end *end;
 } i2cdisp_args;
 
@@ -377,6 +378,13 @@ static int do_i2c_set_display(int argc, char **argv)
 		}
 		/* Check "--cs" option */
 		nerrors +=is_output_gpio(i2cdisp_args.cs,f,&config.CS_pin, false);
+	    /* Check "--mode" option */
+		if (i2cdisp_args.mode->count) {
+			config.mode=i2cdisp_args.mode->ival[0];
+		}
+		else {
+			config.mode = 0;
+		}
 	}
 
 	nerrors +=is_output_gpio(i2cdisp_args.reset,f,&config.RST_pin, false);
@@ -964,6 +972,9 @@ cJSON * i2c_set_display_cb(){
 		cJSON_AddBoolToObject(values,"hf",conf->hflip);
 		cJSON_AddBoolToObject(values,"vf",conf->vflip);
 		cJSON_AddBoolToObject(values,"invert",conf->invert);
+		if(conf->mode>=0){
+			cJSON_AddNumberToObject(values,"mode",conf->mode);
+		}	
 	}
 	return values;
 }
@@ -986,6 +997,7 @@ static void register_i2c_set_display(){
 	i2cdisp_args.rotate = 	arg_lit0("r", "rotate", "Rotate 180 degrees");
 	i2cdisp_args.invert = 	arg_lit0("i", "invert", "Invert colors");
 	i2cdisp_args.clear = 	arg_lit0(NULL, "clear", "clear configuration and return");
+	i2cdisp_args.mode = 	arg_int0("m", "mode", "<n>","SPI Only. Transaction Line Mode (Default 0)");
 	i2cdisp_args.end = 		arg_end(8);
 	const esp_console_cmd_t i2c_set_display= {
 		.command = CFG_TYPE_HW("display"),

components/services/accessors.c

@@ -352,6 +352,10 @@ esp_err_t config_display_set(const display_config_t * config){
 			snprintf(config_buffer2,buffer_size,"%s,speed=%i",config_buffer,config->speed);
 			strcpy(config_buffer,config_buffer2);
 		}
+		if(config->mode >=0 && strcasecmp("SPI",config->type)==0){
+			snprintf(config_buffer2,buffer_size,"%s,mode=%i",config_buffer,config->mode);
+			strcpy(config_buffer,config_buffer2);
+		}
 		snprintf(config_buffer2,buffer_size,"%s,driver=%s%s%s%s",config_buffer,config->drivername,config->hflip?",HFlip":"",config->vflip?",VFlip":"",config->rotate?",rotate":"");
 		strcpy(config_buffer,config_buffer2);
 		log_send_messaging(MESSAGING_INFO,"Updating display configuration to %s",config_buffer);
@@ -465,6 +469,7 @@ const display_config_t * config_display_get(){
 		.rotate = false,
 		.invert = false,
 		.colorswap = 0,
+		.mode = 0,
 	};
 	char *config = config_alloc_get(NVS_TYPE_STR, "display_config");
 	if (!config) {
@@ -484,6 +489,7 @@ const display_config_t * config_display_get(){
 	PARSE_PARAM(config, "address", '=', dstruct.address);
 	PARSE_PARAM(config, "cs", '=', dstruct.CS_pin);
 	PARSE_PARAM(config, "speed", '=', dstruct.speed);
+	PARSE_PARAM(config, "mode", '=', dstruct.mode);
 
 	if (strstr(config, "I2C") ) dstruct.type=i2c_name_type;
 	if (strstr(config, "SPI") ) dstruct.type=spi_name_type;

components/services/accessors.h

@@ -33,6 +33,7 @@ typedef struct {
 	bool rotate;
 	bool invert;
 	int colorswap;
+	int mode;
 } display_config_t;
 
 typedef struct eth_config_struct {