Code moved

native/README_EN.md

@@ -0,0 +1,68 @@
+# Smart intercom based on ESP8266
+**English** | [Русский](https://github.com/Anonym-tsk/smart-domofon/blob/master/native/README.md)
+
+This device can send "door open" command to intercom main unit after receiving of incoming call. It only works with coordinate line intercoms. Tested with Cyfral russian intercom.
+
+---
+
+Enjoy my work? [Help me out](http://yasobe.ru/na/esphome) for a couple of :beers: or a :coffee:!
+
+[![coffee](https://www.buymeacoffee.com/assets/img/custom_images/black_img.png)](http://yasobe.ru/na/esphome)
+
+---
+
+## Parts used
+* NodeMCU v3 x 1
+* Double relay module x1 (or two single relay modules)
+* LED x3 (or one RGB LED)
+* Button x2
+* Optocoupler x1
+* Some resistors
+
+Instead of NodeMCU, you can buy almost any ESP with enough count of GPIO (for example, Wemos D1 Mini). Button and LED are optional.
+
+## Example Parts
+1. [Оптопара PC817B](https://roboshop.spb.ru/PC817B)
+2. [Реле электромеханическое 2-канальное](https://roboshop.spb.ru/SRD-05VDC-SL-C-2-channel-rele)
+3. [NodeMCU V3](https://roboshop.spb.ru/NodeMCU-v3-dev-board)
+4. [RGB светодиод на плате](https://roboshop.spb.ru/RGB-led-module)
+5. [Кнопка тактовая 6х6х13мм KFC-A06-13H](https://roboshop.spb.ru/KFC-A06-13H)
+6. [Провода "мама-мама" 10см, 20 шт.](https://roboshop.spb.ru/female-to-female-line)
+7. [Провода "папа-мама" 10см, 20 шт.](https://roboshop.spb.ru/male-to-female-line)
+8. [Резисторы](https://roboshop.spb.ru/600-resist-set)
+9. [microUSB кабель](https://roboshop.spb.ru/BS-410)
+
+## Scheme
+![Scheme](https://raw.githubusercontent.com/Anonym-tsk/smart-domofon/master/native/scheme.jpeg)
+*Thanks to Oleg Yu*
+
+### This is old deprecated version. Please use new [ESPHome version](https://github.com/Anonym-tsk/smart-domofon/blob/master/esphome/README_EN.md)
+
+## Configuration and build
+1. Fill in WiFi and MQTT credentials in [software.h](https://github.com/Anonym-tsk/smart-domofon/blob/master/native/src/config/software.h)
+2. Fill in `upload_port` in [platformio.ini](https://github.com/Anonym-tsk/smart-domofon/blob/master/native/platformio.ini)
+3. Use [PlatformIO](https://platformio.org/platformio-ide) to build and upload firmware
+
+## Status MQTT messages (domofon/status)
+* 'R' - ready; sent after successfull boot-up or after receiving of 'P' message
+* 'L' - last will message; send when device goes offline
+
+## Incoming MQTT messages (domofon/in)
+* 'O' - door open command
+* 'N' - call reject command (door will not open)
+* 'P' - ping command (answers with 'R')
+
+## Outgoing MQTT messages (domofon/out)
+* 'C' - call; sent after detecting of incoming intercom call
+* 'H' - hangup; sent after detected incoming call finished
+* 'B' - button; sent when "door open" has been performed by green hw button press
+* 'J' - reJected; sent when incoming call has been rejected by red hw button press
+* 'S' - success; sent in response to 'O' or 'N' command
+* 'F' - fail; sent in response to 'O' or 'N' command (this means that 'O' or 'N' command has been received but no incoming call detected)
+
+## Home Assistant integration
+![Home Assistant](https://raw.githubusercontent.com/Anonym-tsk/smart-domofon/master/native/homeassistant/ha.png)
+
+[Full configuration with sensor, switches and automations](https://github.com/Anonym-tsk/smart-domofon/blob/master/native/homeassistant/domofon.yaml)
+
+Put this file into `/config/packages/domofon.yaml` and correct notification service in automations.