esphome_aux_ac_component/examples/advanced/ac_common.yaml

# DON'T COMPILE THIS FILE
# This file contains common settings for all air conditioners of your house
external_components:
  - source: github://GrKoR/esphome_aux_ac_component
    components: [ aux_ac ]
    refresh: 0s

esphome:
  name: $devicename

esp8266:
  board: esp12e

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_pass
  manual_ip:
    static_ip: ${wifi_ip}
    gateway: !secret wifi_gateway
    subnet: !secret wifi_subnet
  ap:
    ssid: ${upper_devicename} Hotspot
    password: !secret wifi_ap_pass
  use_address: ${wifi_ota_ip}

captive_portal:
debug:

logger:
    level: DEBUG
    baud_rate: 0
    # set hardware_uart to UART1 and comment out baud_rate above in case of boot crashes
    # it is suitable if you need hardware loggin
    # hardware_uart: UART1

api:
  password: !secret api_pass

ota:
  - platform: esphome
    password: !secret ota_pass

web_server:
  port: 80
  auth:
    username: !secret web_server_user
    password: !secret web_server_password

# UART0 configuration for AUX air conditioner communication
uart:
  id: ac_uart_bus
  # ATTENTION! Use GPIO4 (D2) and GPIO5 (D1) as the TX and RX for NodeMCU-like boards!
  tx_pin: GPIO1
  rx_pin: GPIO3
  baud_rate: 4800
  data_bits: 8
  parity: EVEN
  stop_bits: 1



climate:
  - platform: aux_ac
    name: ${upper_devicename}
    id: aux_id
    uart_id: ac_uart_bus
    period: 7s
    show_action: true
    display_inverted: true
    optimistic: true
    indoor_temperature:
      name: ${upper_devicename} Indoor Temperature
      id: ${devicename}_indoor_temp
      internal: false
    display_state:
      name: ${upper_devicename} Display State
      id: ${devicename}_display_state
      internal: false
    outdoor_temperature:
      name: ${upper_devicename} Outdoor Temperature
      id: ${devicename}_outdoor_temp
      internal: false
    outbound_temperature:
      name: ${upper_devicename} Coolant Outbound Temperature
      id: ${devicename}_outbound_temp
      internal: false
    inbound_temperature:
      name: ${upper_devicename} Coolant Inbound Temperature
      id: ${devicename}_inbound_temp
      internal: false
    compressor_temperature:
      name: ${upper_devicename} Compressor Temperature
      id: ${devicename}_strange_temp
      internal: false
    defrost_state:
      name: ${upper_devicename} Defrost State
      id: ${devicename}_defrost_state
      internal: false
    inverter_power:
      name: ${upper_devicename} Invertor Power
      id: ${devicename}_inverter_power
      internal: false
    preset_reporter:
      name: ${upper_devicename} Preset Reporter
      id: ${devicename}_preset_reporter
      internal: false
    vlouver_state:
      name: ${upper_devicename} VLouvers State
      id: ${devicename}_vlouver_state
      internal: false
    visual:
      min_temperature: 16
      max_temperature: 32
      temperature_step: 0.5
    supported_modes:
      - HEAT_COOL
      - COOL
      - HEAT
      - DRY
      - FAN_ONLY
    custom_fan_modes:
      - MUTE
      - TURBO
    supported_presets:
      - SLEEP
    custom_presets:
      - CLEAN
      - HEALTH
      - ANTIFUNGUS
    supported_swing_modes:
      - VERTICAL
      - HORIZONTAL
      - BOTH


sensor:
  # just wifi signal strength for debug purpose only
  - platform: wifi_signal
    name: ${upper_devicename} WiFi Signal
    update_interval: 30s
    unit_of_measurement: "dBa"
    accuracy_decimals: 0

  - platform: uptime
    name: ${upper_devicename} Uptime Sensor

switch:
  - platform: template
    name: ${upper_devicename} Display
    lambda: |-
      if (id(${devicename}_display_state).state) {
        return true;
      } else {
        return false;
      }
    turn_on_action:
      - aux_ac.display_on: aux_id
    turn_off_action:
      - aux_ac.display_off: aux_id

button:
  - platform: template
    name: ${upper_devicename} VLouver Stop
    icon: "mdi:circle-small"
    on_press:
      - aux_ac.vlouver_stop: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Swing
    icon: "mdi:pan-vertical"
    on_press:
      - aux_ac.vlouver_swing: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Top
    icon: "mdi:pan-up"
    on_press:
      - aux_ac.vlouver_top: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Middle Above
    icon: "mdi:pan-top-left"
    on_press:
      - aux_ac.vlouver_middle_above: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Middle
    icon: "mdi:pan-left"
    on_press:
      - aux_ac.vlouver_middle: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Middle Below
    icon: "mdi:pan-bottom-left"
    on_press:
      - aux_ac.vlouver_middle_below: aux_id
    
  - platform: template
    name: ${upper_devicename} VLouver Bottom
    icon: "mdi:pan-down"
    on_press:
      - aux_ac.vlouver_bottom: aux_id


number:
  - platform: template
    name: ${upper_devicename} Vertical Louvers
    id: ${devicename}_vlouver
    icon: "mdi:circle-small"
    mode: "slider"
    min_value: 0
    max_value: 6
    step: 1
    update_interval: 2s
    lambda: |-
      return id(${devicename}_vlouver_state).state;
    set_action:
      then:
        - aux_ac.vlouver_set:
            id: aux_id
            position: !lambda "return x;"

  - platform: template
    name: ${upper_devicename} Power Limit
    id: ${devicename}_power_limit
    icon: "mdi:battery-unknown"
    mode: "slider"
    min_value: 30
    max_value: 100
    step: 1
    set_action:
      then:
        - lambda: !lambda "id(aux_id).powerLimitationOnSequence( x );"