Update platformio.ini

Update 1 and added 5 entries

.github/workflows/build.yaml

@@ -1,6 +1,10 @@
 name: Build and Pack
 
-on: [push, pull_request]
+on:
+    push:
+    pull_request:
+    release:
+        types: [released] # Only trigger on published releases (not drafts or pre-released)
 
 jobs:
 #########################################################################################
@@ -304,7 +308,7 @@ jobs:
   prepare-release: 
     runs-on: ubuntu-latest
     needs: [pack-for-update, pack-for-manual_setup, pack-for-remote_setup]
-    if: startsWith(github.ref, 'refs/tags/') 
+    if: github.event_name == 'release' # Only run when the trigger is a release
 
     # Sets permissions of the GITHUB_TOKEN to allow updating the branches
     permissions:
@@ -406,7 +410,7 @@ jobs:
 #########################################################################################
 # Make sure to also update update-webinstaller.yml!
   update-web-installer:
-    if: github.event_name == 'release' && github.event.action == 'published' # Only run on release but not on prerelease
+    if: github.event_name == 'release' # Only run when the trigger is a release
     needs: [prepare-release]
     environment:
       name: github-pages
@@ -444,13 +448,13 @@ jobs:
         sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' webinstaller/manifest.json
 
     - name: Setup Pages
-      uses: actions/configure-pages@v4
+      uses: actions/configure-pages@v5
 
     - name: Upload artifact
-      uses: actions/upload-pages-artifact@v2
+      uses: actions/upload-pages-artifact@v3
       with:
         path: 'webinstaller'
 
     - name: Deploy to GitHub Pages
       id: deployment
-      uses: actions/deploy-pages@v3  # Note: v4 does not work!
+      uses: actions/deploy-pages@v4.0.5  # Note: v4 does not work!

.github/workflows/reply-bot.yaml

@@ -18,7 +18,7 @@ permissions:
 
 jobs:
   comment:
-    runs-on: ubuntu-20.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 

code/components/jomjol_helper/Helper.cpp

@@ -31,7 +31,12 @@ extern "C"
 #include "ClassLogFile.h"
 
 #include "esp_vfs_fat.h"
+
+#if (ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 4, 0))
+#include "esp_private/sdmmc_common.h"
+#else
 #include "../sdmmc_common.h"
+#endif
 
 static const char *TAG = "HELPER";
 
@@ -806,11 +811,21 @@ struct SDCard_Manufacturer_database sd_database[] = {
 		.id = 0x03,
 		.manufacturer = "SanDisk",
 	},
+	{
+		.type = "sd",
+		.id = 0x05,
+		.manufacturer = "Lenovo",
+	},
 	{
 		.type = "sd",
 		.id = 0x08,
 		.manufacturer = "Silicon Power",
 	},
+	{
+		.type = "sd",
+		.id = 0x09,
+		.manufacturer = "ATP",
+	},
 	{
 		.type = "sd",
 		.id = 0x18,
@@ -894,7 +909,27 @@ struct SDCard_Manufacturer_database sd_database[] = {
 	{
 		.type = "sd",
 		.id = 0x89,
-		.manufacturer = "Unknown",
+		.manufacturer = "Netac",
+	},
+	{
+		.type = "sd",
+		.id = 0x9f,
+		.manufacturer = "Kingston/Kodak/Silicon Power",
+	},
+	{
+		.type = "sd",
+		.id = 0xad,
+		.manufacturer = "Amazon Basics/Lexar/OV",
+	},
+	{
+		.type = "sd",
+		.id = 0xdf,
+		.manufacturer = "Lenovo",
+	},
+	{
+		.type = "sd",
+		.id = 0xfe,
+		.manufacturer = "Bekit/Cloudisk/HP/Reletech",
 	},
 };
 

code/platformio.ini

@@ -20,7 +20,7 @@
 [common:esp32-idf]
     extends = common:idf
     ; PlatformIO releases, see https://github.com/platformio/platform-espressif32/releases
-    platform = platformio/espressif32 @ 6.9.0
+    platform = platformio/espressif32 @ 6.11.0
     framework = espidf
     lib_deps = 
         ${common:idf.lib_deps}

param-docs/parameter-pages/InfluxDB/NUMBER.Field.md

@@ -4,4 +4,4 @@ Default Value: `undefined`
 Dedicated definition of the field for InfluxDB use for saving in the Influx database (e.g.: "watermeter/value").
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.Field`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.Field`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/InfluxDBv2/NUMBER.Field.md

@@ -4,4 +4,4 @@ Default Value: `undefined`
 Field for InfluxDB v2 to use for saving.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.Field`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.Field`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/MQTT/MeterType.md

@@ -10,11 +10,11 @@ Alternatively you can set the parameter `DecimalShift` to `3` so the value is co
 List of supported options:
 
 - `other`
-- `water_m3` (uses `m^3/min` as rate)
+- `water_m3` (uses `m^3/h` as rate)
 - `water_l`  (uses `l/h` as rate, not officially supported by Homeassistant!)
 - `water_gal`  (uses `gal/h` as rate, not officially supported by Homeassistant!)
 - `water_ft3` (uses `ft^3/min` as rate)
-- `gas_m3` (uses `m^3/min` as rate)
+- `gas_m3` (uses `m^3/h` as rate)
 - `gas_ft3` (uses `ft^3/min` as rate)
 - `energy_wh` (uses `W` as rate)
 - `energy_kwh` (uses `KW` as rate)

param-docs/parameter-pages/MQTT/NUMBER.DomoticzIDX.md

@@ -4,4 +4,4 @@ Default Value: `0`
 The Idx number for the counter device. Can be obtained from the devices setup page on the Domoticz system.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.DomoticzIDX`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.DomoticzIDX`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.AllowNegativeRates.md

@@ -7,4 +7,4 @@ Allow a meter to count backwards (decreasing values).
     This is unusual (it means there is a negative rate) and not wanted in most cases!
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.AllowNegativeRates`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.AllowNegativeRates`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.AnalogToDigitTransitionStart.md

@@ -9,4 +9,4 @@ See [here](../Watermeter-specific-analog---digit-transition) for details.
 Range: `6.0` .. `9.9`.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.AnalogToDigitTransitionStart`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.AnalogToDigitTransitionStart`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.ChangeRateThreshold.md

@@ -10,18 +10,18 @@ It is only applied to the last digit of the read value (See example below).
 If the read value is within PreValue +/- Threshold, no further calculation is carried out and the Value/Prevalue remains at the old value.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.ChangeRateThreshold`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.ChangeRateThreshold`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).
 
 ## Example
 
 - Smallest ROI provides value for `0.000'x` (Eg. a water meter with 4 pointers behind the decimal point)
 - ChangeRateThreshold = 2
   
-#### With `Extended Resolution` **disabled**
+#### With `ExtendedResolution` **disabled**
 PreValue: `123.456'7` -> Threshold = `+/-0.000'2`.<br>
 All changes between `123.456'5` and `123.456'9` get ignored
 	
-#### With `Extended Resolution` **enabled**
+#### With `ExtendedResolution` **enabled**
 PreValue: `123.456'78` -> Threshold = `+/-0.000'02`.<br>
 All changes between `123.456'76` and `123.456'80` get ignored.
 

param-docs/parameter-pages/PostProcessing/NUMBER.CheckDigitIncreaseConsistency.md

@@ -8,4 +8,4 @@ An additional consistency check.
 It especially improves the zero crossing check between digits.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.CheckDigitIncreaseConsistency`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.CheckDigitIncreaseConsistency`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.DecimalShift.md

@@ -5,4 +5,4 @@ Shift the decimal separator (positiv or negativ).
 Eg. to move from `m³` to `liter` (`1 m³` equals `1000 liters`), you need to set it to `+3`.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.DecimalShift`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.DecimalShift`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.ExtendedResolution.md

@@ -7,4 +7,4 @@ Use the decimal place of the last analog counter for increased accuracy.
     This parameter is only supported on the `*-class*` and `*-const` models! See [Choosing-the-Model](../Choosing-the-Model) for details.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.ExtendedResolution`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.ExtendedResolution`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.IgnoreLeadingNaN.md

@@ -6,4 +6,4 @@ This is only relevant for models which use `N`!
 See [here](../Choosing-the-Model) for details.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.IgnoreLeadingNaN`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.IgnoreLeadingNaN`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.MaxRateType.md

@@ -5,4 +5,4 @@ Defines if the **Change Rate** is calculated as the difference between the last
 as the difference normalized to the interval (`RateChange` = difference per minute).
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.MaxRateType`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.MaxRateType`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.MaxRateValue.md

@@ -6,4 +6,4 @@ Maximum allowed change between two readings, if exceeded the last reading will b
 If negative rate is disallowed and no maximum rate value is set, one false high reading will lead to a period of missing measurements until the measurement reaches the previous false high reading. E.g. if the counter is at `600,00` and it's read incorrectly as` 610,00`, all measurements will be skipped until the counter reaches `610,00`. Setting the MaxRateValue to `0,05` leads to a rejection of all readings with a difference `> 0,05`, in this case `610,00`. The rejection also applies to correct readings with a difference `> 0,05`!
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.MaxRateValue`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.MaxRateValue`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

sd-card/config/config.ini

@@ -43,7 +43,7 @@ AlignmentAlgo = default
 /config/ref1.jpg 442 142
 
 [Digits]
-Model = /config/dig-cont_0712_s3_q.tflite
+Model = /config/dig-cont_0900_s3_q.tflite
 CNNGoodThreshold = 0.5
 ;ROIImagesLocation = /log/digit
 ;ROIImagesRetention = 3
@@ -52,7 +52,7 @@ main.dig2 343 126 30 54 false
 main.dig3 391 126 30 54 false
 
 [Analog]
-Model = /config/ana-cont_1300_s2.tflite
+Model = /config/ana-cont_1500_s2_q.tflite
 CNNGoodThreshold = 0.5
 ;ROIImagesLocation = /log/analog
 ;ROIImagesRetention = 3