Update platformio.ini

Update 1 and added 5 entries

.github/workflows/build.yaml

@@ -1,6 +1,10 @@
 name: Build and Pack
 
-on: [push, pull_request]
+on:
+    push:
+    pull_request:
+    release:
+        types: [released] # Only trigger on published releases (not drafts or pre-released)
 
 jobs:
 #########################################################################################
@@ -84,6 +88,7 @@ jobs:
         cd ../..
 
         cp -r ./sd-card/html/* ./html/
+        rm -f ./html/edit_config_template.html # Remove the config page template, it is no longer needed
         
         echo "Replacing variables..."
         cd html
@@ -285,8 +290,9 @@ jobs:
         rm -rf ./sd-card/html
         rm -rf ./sd-card/demo
         cp -r ./html ./sd-card/ # Overwrite the Web UI with the preprocessed files
+        rm -f ./sd-card/Readme.md
         cp -r ./demo ./sd-card/
-        cd sd-card; zip -r ../manual_setup/sd-card.zip *; cd ..
+        cd sd-card; rm -rf html/param-tooltips; zip -r ../manual_setup/sd-card.zip *; cd ..
         cd ./manual_setup
 
     - name: Upload manual_setup.zip artifact (Firmware + Bootloader + Partitions + Web UI)
@@ -302,7 +308,7 @@ jobs:
   prepare-release: 
     runs-on: ubuntu-latest
     needs: [pack-for-update, pack-for-manual_setup, pack-for-remote_setup]
-    if: startsWith(github.ref, 'refs/tags/') 
+    if: github.event_name == 'release' # Only run when the trigger is a release
 
     # Sets permissions of the GITHUB_TOKEN to allow updating the branches
     permissions:
@@ -404,7 +410,7 @@ jobs:
 #########################################################################################
 # Make sure to also update update-webinstaller.yml!
   update-web-installer:
-    if: github.event_name == 'release' && github.event.action == 'published' # Only run on release but not on prerelease
+    if: github.event_name == 'release' # Only run when the trigger is a release
     needs: [prepare-release]
     environment:
       name: github-pages
@@ -433,22 +439,22 @@ jobs:
     - name: Add binary to Web Installer and update manifest
       run: |
         echo "Updating Web installer to use firmware from ${{ steps.last_release.outputs.tag_name }}..."
-        rm -f docs/binary/firmware.bin
+        rm -f webinstaller/binary/firmware.bin
         wget ${{ github.server_url }}/${{ github.repository }}/releases/download/${{ steps.last_release.outputs.tag_name }}/AI-on-the-edge-device__update__${{ steps.last_release.outputs.tag_name }}.zip
         unzip AI-on-the-edge-device__update__${{ steps.last_release.outputs.tag_name }}.zip
-        cp -f firmware.bin docs/binary/firmware.bin
+        cp -f firmware.bin webinstaller/binary/firmware.bin
         echo "Updating index and manifest file..."
-        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' docs/index.html
+        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' webinstaller/index.html
-        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' docs/manifest.json
+        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' webinstaller/manifest.json
 
     - name: Setup Pages
-      uses: actions/configure-pages@v4
+      uses: actions/configure-pages@v5
 
     - name: Upload artifact
-      uses: actions/upload-pages-artifact@v2
+      uses: actions/upload-pages-artifact@v3
       with:
-        path: 'docs'
+        path: 'webinstaller'
 
     - name: Deploy to GitHub Pages
       id: deployment
-      uses: actions/deploy-pages@v3  # Note: v4 does not work!
+      uses: actions/deploy-pages@v4.0.5  # Note: v4 does not work!

.github/workflows/manual-update-webinstaller.yaml

@@ -1,4 +1,4 @@
-# This updates the Web Installer with the files from the docs folder and the binary of the latest release
+# This updates the Web Installer with the files from the webinstaller folder and the binary of the latest release
 # it only gets run on:
 #  - Manually triggered
 # Make sure to also update the lower part of build.yml!
@@ -11,7 +11,7 @@ on:
 #    branches:
 #    - rolling
 #    paths:
-#    - docs # The path filter somehow does not work, so lets run it on every change to rolling
+#    - webinstaller # The path filter somehow does not work, so lets run it on every change to rolling
 
 jobs:
   manually-update-web-installer:    
@@ -42,13 +42,13 @@ jobs:
     - name: Add binary to Web Installer and update manifest
       run: |
         echo "Updating Web installer to use firmware from ${{ steps.last_release.outputs.tag_name }}..."
-        rm -f docs/binary/firmware.bin
+        rm -f webinstaller/binary/firmware.bin
-        wget https://github.com/jomjol/AI-on-the-edge-device/releases/download/${{ steps.last_release.outputs.tag_name }}/AI-on-the-edge-device__update__${{ steps.last_release.outputs.tag_name }}.zip
+        wget ${{ github.server_url }}/${{ github.repository }}/releases/download/${{ steps.last_release.outputs.tag_name }}/AI-on-the-edge-device__update__${{ steps.last_release.outputs.tag_name }}.zip
         unzip AI-on-the-edge-device__update__${{ steps.last_release.outputs.tag_name }}.zip
-        cp -f firmware.bin docs/binary/firmware.bin
+        cp -f firmware.bin webinstaller/binary/firmware.bin
         echo "Updating index and manifest file..."
-        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' docs/index.html
+        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' webinstaller/index.html
-        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' docs/manifest.json
+        sed -i 's/$VERSION/${{ steps.last_release.outputs.tag_name }}/g' webinstaller/manifest.json
 
     - name: Setup Pages
       uses: actions/configure-pages@v5
@@ -56,7 +56,7 @@ jobs:
     - name: Upload artifact
       uses: actions/upload-pages-artifact@v3
       with:
-        path: 'docs'
+        path: 'webinstaller'
 
     - name: Deploy to GitHub Pages
       id: deployment

.github/workflows/reply-bot.yaml

@@ -18,7 +18,7 @@ permissions:
 
 jobs:
   comment:
-    runs-on: ubuntu-20.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 

code/README.md

@@ -4,7 +4,7 @@
 ```
 git clone https://github.com/jomjol/AI-on-the-edge-device.git
 cd AI-on-the-edge-device
-git checkout rolling
+git checkout main
 git submodule update --init
 ```
 
@@ -12,10 +12,10 @@ git submodule update --init
 ```
 cd /components/submodule-name (e.g. tflite-micro-example)
 git checkout VERSION (e.g. HASH of latest tflite-micro-example build)
-cd ../../ (auf Ebene von code)
+cd ../../ (at the code level)
 git submodule update --init
 ```
-Evt. muss man vorher noch einige Verzeichnisse in compenents von Hand löschen, da sie beim checkout nicht gelöscht wurden (vor update -- init)
+You may need to manually delete some directories in the 'components' folder beforehand, as they were not deleted during checkout (before update -- init)
 
 ## Build and Flash within terminal
 See further down to build it within an IDE.
@@ -51,7 +51,7 @@ pio device monitor -p /dev/ttyUSB0
     ```
     git clone https://github.com/jomjol/AI-on-the-edge-device.git
     cd AI-on-the-edge-device
-    git checkout rolling
+    git checkout main
     git submodule update --init
     ```
 

code/components/jomjol_flowcontroll/ClassFlowPostProcessing.cpp

@@ -898,7 +898,7 @@ bool ClassFlowPostProcessing::doFlow(string zwtime) {
         #endif
 
         if (PreValueUse && NUMBERS[j]->PreValueOkay) {
-            if (NUMBERS[j]->Nachkomma > 0) {
+            if ((NUMBERS[j]->Nachkomma > 0) && (NUMBERS[j]->ChangeRateThreshold > 0)) {
                 double _difference1 = (NUMBERS[j]->PreValue - (NUMBERS[j]->ChangeRateThreshold / pow(10, NUMBERS[j]->Nachkomma)));
                 double _difference2 = (NUMBERS[j]->PreValue + (NUMBERS[j]->ChangeRateThreshold / pow(10, NUMBERS[j]->Nachkomma)));
 

code/components/jomjol_helper/Helper.cpp

@@ -31,7 +31,12 @@ extern "C"
 #include "ClassLogFile.h"
 
 #include "esp_vfs_fat.h"
+
+#if (ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 4, 0))
+#include "esp_private/sdmmc_common.h"
+#else
 #include "../sdmmc_common.h"
+#endif
 
 static const char *TAG = "HELPER";
 
@@ -806,11 +811,21 @@ struct SDCard_Manufacturer_database sd_database[] = {
 		.id = 0x03,
 		.manufacturer = "SanDisk",
 	},
+	{
+		.type = "sd",
+		.id = 0x05,
+		.manufacturer = "Lenovo",
+	},
 	{
 		.type = "sd",
 		.id = 0x08,
 		.manufacturer = "Silicon Power",
 	},
+	{
+		.type = "sd",
+		.id = 0x09,
+		.manufacturer = "ATP",
+	},
 	{
 		.type = "sd",
 		.id = 0x18,
@@ -894,7 +909,27 @@ struct SDCard_Manufacturer_database sd_database[] = {
 	{
 		.type = "sd",
 		.id = 0x89,
-		.manufacturer = "Unknown",
+		.manufacturer = "Netac",
+	},
+	{
+		.type = "sd",
+		.id = 0x9f,
+		.manufacturer = "Kingston/Kodak/Silicon Power",
+	},
+	{
+		.type = "sd",
+		.id = 0xad,
+		.manufacturer = "Amazon Basics/Lexar/OV",
+	},
+	{
+		.type = "sd",
+		.id = 0xdf,
+		.manufacturer = "Lenovo",
+	},
+	{
+		.type = "sd",
+		.id = 0xfe,
+		.manufacturer = "Bekit/Cloudisk/HP/Reletech",
 	},
 };
 

code/components/jomjol_mqtt/interface_mqtt.cpp

@@ -85,7 +85,7 @@ bool MQTTPublish(std::string _key, std::string _content, int qos, bool retained_
             _content.append("..");
         }
 
-        LogFile.WriteToFile(ESP_LOG_DEBUG, TAG, "Published topic: " + _key + ", content: " + _content + " (msg_id=" + std::to_string(msg_id) + ")");
+        LogFile.WriteToFile(ESP_LOG_DEBUG, TAG, "Published topic: " + _key + ", content: " + _content);
         return true;
     }
     else {
@@ -465,7 +465,7 @@ void MQTTconnected(){
        if (subscribeFunktionMap != NULL) {
             for(std::map<std::string, std::function<bool(std::string, char*, int)>>::iterator it = subscribeFunktionMap->begin(); it != subscribeFunktionMap->end(); ++it) {
                 int msg_id = esp_mqtt_client_subscribe(client, it->first.c_str(), 0);
-                LogFile.WriteToFile(ESP_LOG_DEBUG, TAG, "topic " + it->first + " subscribe successful, msg_id=" + std::to_string(msg_id));
+                LogFile.WriteToFile(ESP_LOG_DEBUG, TAG, "topic " + it->first + " subscribe successful");
             }
         }
 

code/components/jomjol_mqtt/server_mqtt.cpp

@@ -174,14 +174,14 @@ bool MQTThomeassistantDiscovery(int qos) {
 	int aFreeInternalHeapSizeBefore = heap_caps_get_free_size(MALLOC_CAP_8BIT | MALLOC_CAP_INTERNAL);
 
     //                                                   Group | Field            | User Friendly Name | Icon                      | Unit | Device Class     | State Class  | Entity Category
-    allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "uptime",          "Uptime",            "clock-time-eight-outline", "s",   "",                "",            "diagnostic", qos);
+    allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "uptime",          "Uptime",            "progress-clock",           "s",   "duration",        "measurement", "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "MAC",             "MAC Address",       "network-outline",          "",    "",                "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "fwVersion",       "Firmware Version",  "application-outline",      "",    "",                "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "hostname",        "Hostname",          "network-outline",          "",    "",                "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "freeMem",         "Free Memory",       "memory",                   "B",   "",                "measurement", "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "wifiRSSI",        "Wi-Fi RSSI",        "wifi",                     "dBm", "signal_strength", "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "CPUtemp",         "CPU Temperature",   "thermometer",              "°C",  "temperature",     "measurement", "diagnostic", qos);
-    allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "interval",        "Interval",          "clock-time-eight-outline", "min",  ""           ,    "measurement", "diagnostic", qos);
+    allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "interval",        "Interval",          "clock-time-eight-outline", "min",  "",               "measurement", "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "IP",              "IP",                "network-outline",           "",    "",               "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "status",          "Status",            "list-status",               "",    "",               "",            "diagnostic", qos);
     allSendsSuccessed |= sendHomeAssistantDiscoveryTopic("",     "flowstart",       "Manual Flow Start", "timer-play-outline",        "",    "",               "",            "",           qos);

code/platformio.ini

@@ -20,7 +20,7 @@
 [common:esp32-idf]
     extends = common:idf
     ; PlatformIO releases, see https://github.com/platformio/platform-espressif32/releases
-    platform = platformio/espressif32 @ 6.9.0
+    platform = platformio/espressif32 @ 6.11.0
     framework = espidf
     lib_deps = 
         ${common:idf.lib_deps}

param-docs/parameter-pages/InfluxDB/NUMBER.Field.md

@@ -4,4 +4,4 @@ Default Value: `undefined`
 Dedicated definition of the field for InfluxDB use for saving in the Influx database (e.g.: "watermeter/value").
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.Field`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.Field`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/InfluxDBv2/NUMBER.Field.md

@@ -4,4 +4,4 @@ Default Value: `undefined`
 Field for InfluxDB v2 to use for saving.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.Field`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.Field`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/MQTT/MeterType.md

@@ -10,11 +10,11 @@ Alternatively you can set the parameter `DecimalShift` to `3` so the value is co
 List of supported options:
 
 - `other`
-- `water_m3` (uses `m^3/min` as rate)
+- `water_m3` (uses `m^3/h` as rate)
 - `water_l`  (uses `l/h` as rate, not officially supported by Homeassistant!)
 - `water_gal`  (uses `gal/h` as rate, not officially supported by Homeassistant!)
 - `water_ft3` (uses `ft^3/min` as rate)
-- `gas_m3` (uses `m^3/min` as rate)
+- `gas_m3` (uses `m^3/h` as rate)
 - `gas_ft3` (uses `ft^3/min` as rate)
 - `energy_wh` (uses `W` as rate)
 - `energy_kwh` (uses `KW` as rate)

param-docs/parameter-pages/MQTT/NUMBER.DomoticzIDX.md

@@ -4,4 +4,4 @@ Default Value: `0`
 The Idx number for the counter device. Can be obtained from the devices setup page on the Domoticz system.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.DomoticzIDX`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.DomoticzIDX`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.AllowNegativeRates.md

@@ -7,4 +7,4 @@ Allow a meter to count backwards (decreasing values).
     This is unusual (it means there is a negative rate) and not wanted in most cases!
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.AllowNegativeRates`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.AllowNegativeRates`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.AnalogToDigitTransitionStart.md

@@ -9,4 +9,4 @@ See [here](../Watermeter-specific-analog---digit-transition) for details.
 Range: `6.0` .. `9.9`.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.AnalogToDigitTransitionStart`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.AnalogToDigitTransitionStart`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.ChangeRateThreshold.md

@@ -1,7 +1,7 @@
 # Parameter `ChangeRateThreshold`
 Default Value: `2`
 
-Range: `1` .. `9`.
+Range: `0` .. `9`.
 
 Threshold parameter for change rate detection.<br>
 This parameter is intended to compensate for small reading fluctuations that occur when the meter does not change its value for a long time (e.g. at night) or slightly turns backwards. This can eg. happen on watermeters.
@@ -10,18 +10,18 @@ It is only applied to the last digit of the read value (See example below).
 If the read value is within PreValue +/- Threshold, no further calculation is carried out and the Value/Prevalue remains at the old value.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.ChangeRateThreshold`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.ChangeRateThreshold`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).
 
 ## Example
 
 - Smallest ROI provides value for `0.000'x` (Eg. a water meter with 4 pointers behind the decimal point)
 - ChangeRateThreshold = 2
   
-#### With `Extended Resolution` **disabled**
+#### With `ExtendedResolution` **disabled**
 PreValue: `123.456'7` -> Threshold = `+/-0.000'2`.<br>
 All changes between `123.456'5` and `123.456'9` get ignored
 	
-#### With `Extended Resolution` **enabled**
+#### With `ExtendedResolution` **enabled**
 PreValue: `123.456'78` -> Threshold = `+/-0.000'02`.<br>
 All changes between `123.456'76` and `123.456'80` get ignored.
 

param-docs/parameter-pages/PostProcessing/NUMBER.CheckDigitIncreaseConsistency.md

@@ -8,4 +8,4 @@ An additional consistency check.
 It especially improves the zero crossing check between digits.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.CheckDigitIncreaseConsistency`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.CheckDigitIncreaseConsistency`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.DecimalShift.md

@@ -5,4 +5,4 @@ Shift the decimal separator (positiv or negativ).
 Eg. to move from `m³` to `liter` (`1 m³` equals `1000 liters`), you need to set it to `+3`.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.DecimalShift`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.DecimalShift`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.ExtendedResolution.md

@@ -7,4 +7,4 @@ Use the decimal place of the last analog counter for increased accuracy.
     This parameter is only supported on the `*-class*` and `*-const` models! See [Choosing-the-Model](../Choosing-the-Model) for details.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.ExtendedResolution`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.ExtendedResolution`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.IgnoreLeadingNaN.md

@@ -6,4 +6,4 @@ This is only relevant for models which use `N`!
 See [here](../Choosing-the-Model) for details.
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.IgnoreLeadingNaN`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.IgnoreLeadingNaN`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.MaxRateType.md

@@ -5,4 +5,4 @@ Defines if the **Change Rate** is calculated as the difference between the last
 as the difference normalized to the interval (`RateChange` = difference per minute).
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.MaxRateType`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.MaxRateType`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

param-docs/parameter-pages/PostProcessing/NUMBER.MaxRateValue.md

@@ -6,4 +6,4 @@ Maximum allowed change between two readings, if exceeded the last reading will b
 If negative rate is disallowed and no maximum rate value is set, one false high reading will lead to a period of missing measurements until the measurement reaches the previous false high reading. E.g. if the counter is at `600,00` and it's read incorrectly as` 610,00`, all measurements will be skipped until the counter reaches `610,00`. Setting the MaxRateValue to `0,05` leads to a rejection of all readings with a difference `> 0,05`, in this case `610,00`. The rejection also applies to correct readings with a difference `> 0,05`!
 
 !!! Note
-    This parameter must be prefixed with `<NUMBER>` followed by a dot (eg. `main.MaxRateValue`). `<NUMBER>` is the name of the number sequence  defined in the ROI's.
+    If you edit the config file manually, you must prefix this parameter with `<NUMBER>` followed by a dot (eg. `main.MaxRateValue`). The reason is that this parameter is specific for each `<NUMBER>` (`<NUMBER>` is the name of the number sequence defined in the ROI's).

sd-card/Readme.md

@@ -0,0 +1,5 @@
+# SD Card content
+This folder contains the files which are required to setup the SD card.
+
+❗ Do not directly copy this folder onto your SD card, **it will not work!** Instead, you can use any of the artifacts generaded in any of the Pipeline runs of the [Build-Pipeline](https://github.com/jomjol/AI-on-the-edge-device/actions/workflows/build.yaml).
+The files in the `html` folder here only serve as templates. The real `html` folder get generated using the Github actions.

sd-card/config/config.ini

@@ -43,7 +43,7 @@ AlignmentAlgo = default
 /config/ref1.jpg 442 142
 
 [Digits]
-Model = /config/dig-cont_0712_s3_q.tflite
+Model = /config/dig-cont_0900_s3_q.tflite
 CNNGoodThreshold = 0.5
 ;ROIImagesLocation = /log/digit
 ;ROIImagesRetention = 3
@@ -52,7 +52,7 @@ main.dig2 343 126 30 54 false
 main.dig3 391 126 30 54 false
 
 [Analog]
-Model = /config/ana-cont_1300_s2.tflite
+Model = /config/ana-cont_1500_s2_q.tflite
 CNNGoodThreshold = 0.5
 ;ROIImagesLocation = /log/analog
 ;ROIImagesRetention = 3
@@ -73,7 +73,7 @@ main.MaxRateValue = 0.05
 main.ExtendedResolution = false
 main.IgnoreLeadingNaN = false
 ErrorMessage = true
-CheckDigitIncreaseConsistency = false
+main.CheckDigitIncreaseConsistency = false
 
 ;[MQTT]
 ;Uri = mqtt://IP-ADRESS:1883

sd-card/demo/config.ini

@@ -43,14 +43,14 @@ AlignmentAlgo = default
 /config/ref1.jpg 536 113
 
 [Digits]
-Model = /config/dig-cont_0710_s3_q.tflite
+Model = /config/dig-cont_0810_s3_q.tflite
 CNNGoodThreshold = 0.5
 ;ROIImagesLocation = /log/digit
 ;ROIImagesRetention = 3
 main.dig1 438 62 49 71 false
 
 [Analog]
-Model = /config/ana-cont_1300_s2.tflite
+Model = /config/ana-cont_1400_s2_q.tflite
 ;ROIImagesLocation = /log/analog
 ;ROIImagesRetention = 3
 main.ana1 452 199 120 120 false
@@ -67,7 +67,7 @@ main.AllowNegativeRates = true
 main.ExtendedResolution = true
 main.IgnoreLeadingNaN = false
 ErrorMessage = true
-CheckDigitIncreaseConsistency = false
+main.CheckDigitIncreaseConsistency = false
 
 ;[MQTT]
 ;Uri = mqtt://IP-ADRESS:1883
@@ -76,11 +76,14 @@ CheckDigitIncreaseConsistency = false
 ;user = USERNAME
 ;password = PASSWORD
 RetainMessages = false
+;DomoticzTopicIn = undefined
+;main.DomoticzIDX = undefined
 HomeassistantDiscovery = false
 ;MeterType = other
 ;CACert = /config/certs/RootCA.pem
 ;ClientCert = /config/certs/client.pem.crt
 ;ClientKey = /config/certs/client.pem.key
+;ValidateServerCert = true
 
 ;[InfluxDB]
 ;Uri = undefined
@@ -133,4 +136,3 @@ TimeZone = CET-1CEST,M3.5.0,M10.5.0/3
 RSSIThreshold = -75
 CPUFrequency = 160
 SetupMode = false
- 

sd-card/html/edit_config_template.html

@@ -968,8 +968,8 @@
                 <label for=PostProcessing_ChangeRateThreshold_enabled><class id="PostProcessing_ChangeRateThreshold_text" style="color:black;">Change Rate Threshold</class></label>
             </td>
             <td>
-                <input required type="number" id="PostProcessing_ChangeRateThreshold_value1" step="1" min="1" max="9" value="2"
+                <input required type="number" id="PostProcessing_ChangeRateThreshold_value1" step="1" min="0" max="9" value="2"
-                    oninput="(!validity.rangeUnderflow||(value=1)) && (!validity.rangeOverflow||(value=9)) && 
+                    oninput="(!validity.rangeUnderflow||(value=0)) && (!validity.rangeOverflow||(value=9)) && 
                         (!validity.stepMismatch||(value=parseInt(this.value)));">
             </td>
             <td>$TOOLTIP_PostProcessing_NUMBER.ChangeRateThreshold</td>

webinstaller/Readme.md

@@ -0,0 +1,3 @@
+# Webinstaller
+This folder is used to provide the required files to generate the [Web-Installer](https://jomjol.github.io/AI-on-the-edge-device/).
+The Webinstaller gets automatically updated on a release using the Github actions.

webinstaller/binary/Readme.md

@@ -0,0 +1,2 @@
+# Binary folder of the webinstaller
+The firmware itself (`firmware.bin`) gets copied to this folder through the Github action.

webinstaller/index.html

@@ -67,21 +67,19 @@
 
    <div class="footer">
       <div class="footer-section">
-       <span>Support & Contact Us</span>
+       <span>Support & Contact</span>
        <a href="https://github.com/jomjol/AI-on-the-edge-device" target="_blank" title="GitHub">
-          <img src="https://github.com/jomjol/AI-on-the-edge-device/images/github-logo.png" alt="GitHub">
+          <img src="https://raw.githubusercontent.com/jomjol/AI-on-the-edge-device/refs/heads/main/images/github-logo.png" alt="GitHub">
-       </a>
-          <img src="https://github.com/jomjol/AI-on-the-edge-device/images/gmail-logo.png" alt="Email">
        </a>
        <a href="https://github.com/jomjol/AI-on-the-edge-device/discussions" target="_blank" title="GitHub">
-          <img src="https://github.com/jomjol/AI-on-the-edge-device/images/discussion-logo" alt="GitHub">
+          <img src="https://raw.githubusercontent.com/jomjol/AI-on-the-edge-device/refs/heads/main/images/discussion-logo.png" alt="GitHub">
        </a>
 	
     </div>
       <div class="footer-section">
          <span>Donations</span>
          <a href="https://www.paypal.com/donate?hosted_button_id=8TRSVYNYKDSWL" target="_blank" title="Donate via PayPal">
-            <img src="https://github.com/jomjol/AI-on-the-edge-device/images/paypal.png" alt="PayPal" style="width: 60px; height: auto;">
+            <img src="https://raw.githubusercontent.com/jomjol/AI-on-the-edge-device/refs/heads/main/images/paypal.png" alt="PayPal" style="width: 60px; height: auto;">
          </a>
       </div>
    </div>